![]() I haven’t created any image files larger than 2GB, I’m assuming if you have a card larger than 2GB you plan to setup your SD card as multiple drives (see Section 3.2 below). I’ve created drive images (bit-by-bit copies including the boot drivers and partition table) containing the minimum versions* of System 6.0.8 and System 7.5.5, and several utilities and drivers. Run the scsi2sd-util software (figure 2).Download the latest firmware and scsi2sd-util software for your SCSI2SD adapter (figure 1).Connect your SCSI2SD board to your modern system via USB.Insert the SD card in to your SCSI2SD, connect to your Mac and boot, NOTE: for the Plus the SCSI2SD needs to be connected to a power source to work, USB power is the easiest.Use balenaEtcher (Windows/Linux/Mac) or DD (Windows/Linux/Mac) to write my drive image file to an SD card.Download my SCSI2SD v3/v4/v5.x config files, select the right one (1/2GB and plus/not plus), load it in the SCSI2SD setup software, and write to your SCSI2SD adapter (settings stored on the adapter, NOT your card), may work with v.6.x but I’m not sure (see section 3 for settings).Download my 2GB System 6.0.8 or System 7.5.5 drive image (compressed to around 50Megs), remember not all 68k Macs support all system versions, System 7.5.5 is the most supported but requires 2MB ram minimum.Update your SCSI2SD with the latest firmware.These steps are a summary of the information in the sections below A SD or MicroSD card you plan to use with your SCSI2SD adaptor.A SCSI2SD adaptor, you MAY be able to use these images with a Compact Flash card of the correct size and a CF2SCSI adapter, if you can, let me know.* There are some rare 3rd party upgrades that add a SCSI port to 512K systems. You will need to use one of the other setup methods I’ve previously identified, with the best option being buying and using Floppy-Emu to boot from 400KB SS SD floppy disk images. These three 68k systems do not support internal or external SCSI. The SCS2SD will work for the majority of 68k Macintosh computers except: The 128K, 512K*, 512Ke*. Note, for Powerbook systems that only support 2.5″ SCSI drives, a Powerbook Edition of the SD2SCSI adaptor can be used to replace the internal drive. A working internal or external SCSI connection, you will need to have an SCSI enclosure or an external adapter for your SCSI2SD adaptor so to use it externally.If your 68k Macintosh does not turn on, or does not show the insert disk icon, you may need to do some repair work before you proceed. A 68k Macintosh that turns on, and is prompting you to insert a disk.I’ve added an entry to my site with details of how I’ve set up a 32GB SD card for use in my Macintosh LC 475 with my Apple IIe card (4 ProDOS partitions) What you need Note, this is one of many, many options available to you for booting your classic Macintosh. Mount the ESXi Installation ISO and copy all the contents from the ISO to the USB flash drive.So, similar to my entry on setting up using a floppy disk, and setting up using an Iomega Zip Drive, I created boot images for System 6.0.8 and System 7.5.5 for setting up an SD card for use with SCSI2SD. Flag the first partition on the volume as active and bootable.Start the command line partitoner fdisk in interactive mode (You will need administrative privileges for this). Don’t forget to use the disk# number obtained in step 2. Unmount the USB Drive, Note: This is not the same as Eject. diskutil eraseDisk MS-DOS "ESXI" MBR disk# Now we need to format the drive with filesystem FAT32 and partition map MBR using the following command. You should now see another disk show up, in my case disk3. Insert the USB Flash then run the diskutil list command again. Open Terminal and list the mounted disks using the diskutil list command. Download the ESXi Installation ISO (I used ESXi 7.0b).
0 Comments
Leave a Reply. |